- #Eve ng install juniper vqfx how to#
- #Eve ng install juniper vqfx full#
- #Eve ng install juniper vqfx code#
#Eve ng install juniper vqfx full#
I played with this stuff a little bit and created a couple of new examples using full vQFX option (e.g.
![eve ng install juniper vqfx eve ng install juniper vqfx](https://www.2stacks.net/assets/images/20191105/add_node_1.png)
And I also hope there is no need to present Ansible.
What is Vagrant? Let me quote official website: “Vagrant is a tool for building and managing virtual machine environments in a single workflow. Vagrant gives you a disposable environment and consistent workflow for developing and testing infrastructure management scripts.” I hope you already knew that. Q2) I have read and you mention that your VLANs must always match on both devices (vQFX-RE7 and vQFX-RE8 in this case), but what happens if you need to add a VLAN, will it take the MC-LAG down and blackhole the traffic toward the server? Assuming you do one device at a time, you will have a short inconsistency.Did you know that Juniper vQFX images are available in Vagrant Cloud? There is vQFX RE image and vQFX PFE one. You can use only RE image to build simple topologies, or pair every RE with PFE to use more complex protocols. There is also a bunch of examples in Juniper’s github repository. Q1) Would you expect to see “live traffic” from the vQFX-RE (the server) to cross the ICCP link ae0 between vQFX-RE7 and vQFX-RE8 or just control traffic to keep the MC-LAG up? I am asking to see if there are special requirements when sizing the ICCP links, for either path redundancy of to guarantee that traffic can do east-west without congestion. Being new to the concept of MC-LAG with Juniper (and likewise for other vendors e.g. I will give you more explanation on this Topic later because as you might have heard my JNCIE-DC is booked for the 14th of February (therefore not so much time to write detailed Blogposts) and time is slowly running away… Okay just kidding – time just took a SPRINT towards my deadline… However, my beard looks fine so far… ICCP IP (Local) and Peer IP (who would have guessed this…) The following settings must be unique for each Member of the MC-LAG: When configuring MC-LAG always remember that the following settings must match on both Members of the MC-LAG: Set chassis aggregated-devices ethernet device-count 1 Set interfaces ae0 unit 0 family ethernet-switching vlan members v100 Set multi-chassis multi-chassis-protection 3.3.3.1 interface ae0 Set protocols iccp peer 3.3.3.1 liveness-detection transmit-interval minimum-interval 9000 Set protocols iccp peer 3.3.3.1 liveness-detection minimum-receive-interval 9000 Set protocols iccp peer 3.3.3.1 redundancy-group-id-list 1 Set interfaces irb unit 500 family inet address 3.3.3.2/24 Set interfaces ae1 aggregated-ether-options mc-ae status-control active Set interfaces ae1 aggregated-ether-options mc-ae chassis-id 0 Set multi-chassis multi-chassis-protection 3.3.3.2 interface ae0 Set protocols rstp interface ae1 mode point-to-point Set protocols rstp interface ae0 mode point-to-point Set protocols iccp peer 3.3.3.2 liveness-detection transmit-interval minimum-interval 9000 Set protocols iccp peer 3.3.3.2 liveness-detection minimum-receive-interval 9000 Set protocols iccp peer 3.3.3.2 redundancy-group-id-list 1 Set interfaces irb unit 500 family inet address 3.3.3.1/24 Set interfaces ae1 unit 0 family ethernet-switching vlan members v100 Set interfaces ae1 unit 0 family ethernet-switching interface-mode trunk Set interfaces ae1 aggregated-ether-options mc-ae redundancy-group 1 Set interfaces ae1 aggregated-ether-options mc-ae init-delay-time 240 Set interfaces ae1 aggregated-ether-options mc-ae status-control standby Set interfaces ae1 aggregated-ether-options mc-ae mode active-active Set interfaces ae1 aggregated-ether-options mc-ae chassis-id 1 Set interfaces ae1 aggregated-ether-options mc-ae mc-ae-id 1 Set interfaces ae1 aggregated-ether-options lacp admin-key 1 Set interfaces ae1 aggregated-ether-options lacp system-id 00:01:01:01:01:01 Set interfaces ae1 aggregated-ether-options lacp active Set interfaces ae0 unit 0 family ethernet-switching vlan members v500 Set interfaces ae0 unit 0 family ethernet-switching interface-mode trunk Set interfaces xe-0/0/0 ether-options 802.3ad ae1 Set interfaces xe-0/0/2 ether-options 802.3ad ae0 Set interfaces xe-0/0/1 ether-options 802.3ad ae0 Set chassis aggregated-devices ethernet device-count 2
![eve ng install juniper vqfx eve ng install juniper vqfx](https://i.ytimg.com/vi/WWmEx6yZkZQ/maxresdefault.jpg)
#Eve ng install juniper vqfx code#
Here’s the very simple Topology (click to enlarge):Īnd here’s the Code – as you can see it’s not that hard but you have to remember some things: vQFX-RE7 I personally found this pretty straight forward to configure but since I recieved so many Mails asking me to show this, I will do.
#Eve ng install juniper vqfx how to#
Today I’m gonna show you how to implement MC-LAG on the vQFX (QFX10k codebase) on EVE-NG.